<?xml version="1.0" encoding="utf-8" standalone="yes"?><rss version="2.0" xmlns:atom="http://www.w3.org/2005/Atom"><channel><title>Open Timegrapher</title><link>https://opentimegrapher.org/</link><description>Recent content on Open Timegrapher</description><generator>Hugo</generator><language>en</language><atom:link href="https://opentimegrapher.org/index.xml" rel="self" type="application/rss+xml"/><item><title>1. What a Timegrapher Measures</title><link>https://opentimegrapher.org/guide/01-what-a-timegrapher-measures/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/01-what-a-timegrapher-measures/</guid><description>&lt;p>A timegrapher listens to the escapement and times its sounds. From those
times it works out how fast the watch runs, how far the balance swings,
and how evenly the two halves of each swing are timed.&lt;/p>
&lt;p>It can&amp;rsquo;t see the balance, feel the mainspring or look at a tooth. Knowing
which sound each number comes from tells you when to trust a number, and
when the microphone, not the watch, has changed.&lt;/p></description></item><item><title>M1. Beats</title><link>https://opentimegrapher.org/math/m1-beats/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m1-beats/</guid><description>&lt;p>Every reading starts from a list of beats: a time, a number and a
quality for each tick and tock heard. This page says how the app finds
them in the sound.&lt;/p>
&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>A &lt;strong>beat&lt;/strong> is one tick or tock found in the sound. Each has:&lt;/p>
&lt;ul>
&lt;li>&lt;strong>a time:&lt;/strong> when its drop was heard, on the sound card&amp;rsquo;s clock;&lt;/li>
&lt;li>&lt;strong>a number:&lt;/strong> counted from the take&amp;rsquo;s start, with any missed beats
counted too, so beat 1,000 is always 1,000 beats after beat 0;&lt;/li>
&lt;li>&lt;strong>a quality:&lt;/strong> how well its sound matches the take&amp;rsquo;s typical beat.
A typical beat scores about 1. Only beats scoring over 0.4, the &lt;strong>good
beats&lt;/strong>, are timed or measured.&lt;/li>
&lt;/ul>
&lt;p>Even-numbered beats are &lt;strong>Tick&lt;/strong>, odd-numbered beats are &lt;strong>Tock&lt;/strong>.&lt;/p></description></item><item><title>2. Your First Take</title><link>https://opentimegrapher.org/guide/02-your-first-take/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/02-your-first-take/</guid><description>&lt;p>&lt;strong>Quick Listen&lt;/strong> is the fastest way to measure a watch. Put it on the
microphone and press one button. There is no watch to set up first. This
chapter walks through it once, from installing the app to saving the
take.&lt;/p>
&lt;h2 id="what-you-need">What You Need&lt;/h2>
&lt;ul>
&lt;li>&lt;strong>The app&lt;/strong> for your computer, from the
&lt;a href="https://github.com/peterhudson/timegrapher/releases/latest">Releases page&lt;/a>.
&lt;a href="https://github.com/peterhudson/timegrapher/blob/v1.0.1/docs/reference/install.md">Installing and updating&lt;/a> has the details for macOS,
Windows and Linux.&lt;/li>
&lt;li>&lt;strong>A timegrapher microphone:&lt;/strong> a contact microphone in a watch holder.
An ordinary microphone often hears the loud drop but misses the quiet
unlock, so rate works and amplitude doesn&amp;rsquo;t.&lt;/li>
&lt;li>&lt;strong>A mechanical watch&lt;/strong> with a Swiss lever escapement, fully wound.&lt;/li>
&lt;li>&lt;strong>Its calibre&lt;/strong>, if you know it. The calibre gives the lift angle,
which amplitude needs.&lt;/li>
&lt;/ul>
&lt;h2 id="install-and-open">Install and Open&lt;/h2>
&lt;ul>
&lt;li>&lt;strong>macOS:&lt;/strong> open the disk image and drag the app to Applications.&lt;/li>
&lt;li>&lt;strong>Windows and Linux:&lt;/strong> extract the whole download and run the app from
that folder. Keep its files together.&lt;/li>
&lt;li>The builds aren&amp;rsquo;t signed, so the system may ask you to approve the
first launch. Allow microphone access when asked.&lt;/li>
&lt;/ul>
&lt;h2 id="set-up-the-microphone">Set Up the Microphone&lt;/h2>
&lt;p>The first time the app opens, it asks you to set up the microphone. It
starts listening at once, so you can see the watch as you set it up.&lt;/p></description></item><item><title>M2. Rate</title><link>https://opentimegrapher.org/math/m2-rate/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m2-rate/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>The &lt;strong>rate&lt;/strong> is how many seconds a day the watch would gain (+) or lose
(−) if it kept running exactly as it does over the reading.&lt;/p>
&lt;h2 id="how-it-is-worked-out">How It Is Worked Out&lt;/h2>
&lt;p>The app fits one straight line through the good beats&amp;rsquo; times against
their numbers:&lt;/p>
&lt;div class="highlight">&lt;pre tabindex="0" class="chroma">&lt;code class="language-text" data-lang="text">&lt;span class="line">&lt;span class="cl">time of beat k = t0 + P × k ± e/2
&lt;/span>&lt;/span>&lt;/code>&lt;/pre>&lt;/div>&lt;ul>
&lt;li>&lt;code>P&lt;/code> is the watch&amp;rsquo;s beat period, the time from one beat to the next.&lt;/li>
&lt;li>&lt;code>e/2&lt;/code> is added to Ticks and taken from Tocks: half the beat error, so
the two sides&amp;rsquo; uneven timing doesn&amp;rsquo;t tilt the line (M5).&lt;/li>
&lt;li>The line is fitted by least squares, then fitted twice more without the
beats over 5 robust standard deviations from it.&lt;/li>
&lt;/ul>
&lt;p>The rate compares &lt;code>P&lt;/code> with the beat period the movement is made for,
3,600 s over the beat rate:&lt;/p></description></item><item><title>3. Setting Up the Microphone</title><link>https://opentimegrapher.org/guide/03-setting-up-the-microphone/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/03-setting-up-the-microphone/</guid><description>&lt;p>A good rate needs only the loud drop. A good amplitude and beat error
also need the quiet unlock, timed the same way every beat. So a setup
that gives a steady rate can still give a poor amplitude.&lt;/p>
&lt;p>The aim: firm contact, enough level, no clipping, and no processing of
the sound on its way in.&lt;/p>
&lt;h2 id="settings--microphone">Settings &amp;gt; Microphone&lt;/h2>
&lt;p>Open Settings with the gear at the right of the top row, &lt;strong>Edit &amp;gt;
Settings…&lt;/strong> (&lt;strong>Timegrapher &amp;gt; Settings…&lt;/strong> on a Mac), or &lt;strong>Ctrl+,&lt;/strong>
(&lt;strong>Cmd+,&lt;/strong> on a Mac). Then pick &lt;strong>Microphone&lt;/strong>.&lt;/p></description></item><item><title>M3. The Sound Card's Clock</title><link>https://opentimegrapher.org/math/m3-the-sound-cards-clock/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m3-the-sound-cards-clock/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>The sound card counts samples by its own quartz crystal. If the crystal
runs fast, the card&amp;rsquo;s second is short, and every beat seems to come a
little late: the watch reads slow. The error is given in &lt;strong>parts per
million (ppm)&lt;/strong>, + when the card runs fast.&lt;/p>
&lt;table>
 &lt;thead>
 &lt;tr>
 &lt;th>Card error&lt;/th>
 &lt;th>Rate error&lt;/th>
 &lt;/tr>
 &lt;/thead>
 &lt;tbody>
 &lt;tr>
 &lt;td>1 ppm&lt;/td>
 &lt;td>0.09 s/d&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>10 ppm&lt;/td>
 &lt;td>0.86 s/d&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>20 ppm&lt;/td>
 &lt;td>1.73 s/d&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>50 ppm&lt;/td>
 &lt;td>4.32 s/d&lt;/td>
 &lt;/tr>
 &lt;/tbody>
&lt;/table>
&lt;p>A sound card&amp;rsquo;s crystal is commonly 10 to 50 ppm off, and holds that error
steadily. Two sound cards can read the same watch a few s/d apart.&lt;/p></description></item><item><title>4. The Window</title><link>https://opentimegrapher.org/guide/04-the-window/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/04-the-window/</guid><description>&lt;p>The window has one top row, two views and a status bar.&lt;/p>
&lt;ul>
&lt;li>&lt;strong>The Bench&lt;/strong> shows one take: live from the microphone, or opened from
a file. Its readings cards sit across the top, with panes below.&lt;/li>
&lt;li>&lt;strong>Watches&lt;/strong> lists your watches and their takes. See chapter 22.&lt;/li>
&lt;/ul>
&lt;p>The app always opens on the Bench. Switching views never stops, pauses or
saves a take.&lt;/p>
&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/bench.png" alt="The Bench with a take opened, marks 1 to 12">&lt;/p></description></item><item><title>M4. Amplitude and Lift Angle</title><link>https://opentimegrapher.org/math/m4-amplitude-and-lift-angle/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m4-amplitude-and-lift-angle/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>The &lt;strong>amplitude&lt;/strong> is how far the balance turns from rest to the end of its
swing, in degrees.&lt;/p>
&lt;p>The &lt;strong>lift angle&lt;/strong> is the arc of the balance&amp;rsquo;s swing during which the
impulse pin is in the fork: from the unlock to the drop. It is set by the
movement&amp;rsquo;s design. The calibre table gives it where it is known.&lt;/p>
&lt;h2 id="how-it-is-worked-out">How It Is Worked Out&lt;/h2>
&lt;p>The balance swings like a pendulum: its angle follows a sine wave of
amplitude &lt;code>A&lt;/code> and period &lt;code>T&lt;/code>, one full oscillation, two beats. Near the
middle of its swing it passes through the lift angle &lt;code>L&lt;/code>, centred on the
rest point. The time &lt;code>t&lt;/code> it takes is short when the swing is wide, since
the balance is moving fastest there.&lt;/p></description></item><item><title>5. The Readings Cards and the Calibre Card</title><link>https://opentimegrapher.org/guide/05-the-readings-cards/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/05-the-readings-cards/</guid><description>&lt;p>The six cards across the top of the Bench hold everything the app knows
about the take on show: where the watch lies, what it is, whether it is
being heard, and the three readings.&lt;/p>
&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/readings-cards.png" alt="A Quick Listen take a minute in, marks 1 to 14 on the six cards">&lt;/p>
&lt;p>Every card has the same three rows, so the titles, the big figures and
the controls each read in one line across:&lt;/p></description></item><item><title>M5. Beat Error</title><link>https://opentimegrapher.org/math/m5-beat-error/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m5-beat-error/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>The &lt;strong>beat error&lt;/strong> is how unevenly the two halves of the balance&amp;rsquo;s swing
are timed: half the difference between the Tick-to-Tock and Tock-to-Tick
intervals, in milliseconds.&lt;/p>
&lt;p>If one interval is 124.7 ms and the next 125.3 ms, the beat error is
half of 0.6 ms: &lt;strong>0.30 ms&lt;/strong>.&lt;/p>
&lt;p>It is signed: &lt;strong>+ when the Tick comes late&lt;/strong>. The cards and charts show
its size; the sign is in the command line&amp;rsquo;s JSON.&lt;/p></description></item><item><title>6. The Paper Strip</title><link>https://opentimegrapher.org/guide/06-paper-strip/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/06-paper-strip/</guid><description>&lt;p>The Paper Strip draws one dot for every beat, the way a printing
timegrapher marks its paper. It shows what the readings summarise: how
steadily the watch keeps time, beat by beat.&lt;/p>
&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/paper-strip.png" alt="The Paper Strip on an opened take, marks 1 to 14">&lt;/p>
&lt;h2 id="reading-the-strip">Reading the Strip&lt;/h2>
&lt;ul>
&lt;li>&lt;strong>Along the strip&lt;/strong> is time: the take&amp;rsquo;s minutes and seconds.&lt;/li>
&lt;li>&lt;strong>Across the strip&lt;/strong> is how early or late each beat came against a
perfect clock beating exactly at the nominal beat rate, every 125 ms at
28,800 bph. &lt;strong>Early&lt;/strong> is up, &lt;strong>Late&lt;/strong> down (with Direction set to
Down, early is to the right): the words Witschi&amp;rsquo;s training course uses
(doc. 71.1010D35e, p. 6).&lt;/li>
&lt;li>&lt;strong>Tick&lt;/strong> dots are blue and &lt;strong>Tock&lt;/strong> dots orange (mark 13).&lt;/li>
&lt;li>&lt;strong>The amplitude&lt;/strong> is drawn over the dots as a violet line, on its own
scale at the right (mark 14). The rate and the beat error can be drawn
the same way (mark 1).&lt;/li>
&lt;/ul>
&lt;table>
 &lt;thead>
 &lt;tr>
 &lt;th>What you see&lt;/th>
 &lt;th>What it means&lt;/th>
 &lt;/tr>
 &lt;/thead>
 &lt;tbody>
 &lt;tr>
 &lt;td>Two flat lines&lt;/td>
 &lt;td>The watch keeps the nominal rate.&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>Two lines sloping up&lt;/td>
 &lt;td>Each beat comes a little sooner: the watch gains.&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>Two lines sloping down&lt;/td>
 &lt;td>The watch loses.&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>A gap between the two lines&lt;/td>
 &lt;td>The beat error, timed from the drop.&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>Lines that bend&lt;/td>
 &lt;td>The rate is changing.&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>Dots scattered across the lines&lt;/td>
 &lt;td>Jitter: uneven beats, or a poor sound.&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>A sudden step in both lines&lt;/td>
 &lt;td>A jump: a knock, or lost sound. The readings skip it.&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>Faint grey dots&lt;/td>
 &lt;td>Beats in the settling time, or masked. They aren&amp;rsquo;t read.&lt;/td>
 &lt;/tr>
 &lt;/tbody>
&lt;/table>
&lt;p>&lt;strong>A line that runs off one edge comes back on the other,&lt;/strong> like paper
wrapped round a drum. So the strip&amp;rsquo;s &lt;strong>Width&lt;/strong> is its zoom.&lt;/p></description></item><item><title>M6. Averaging, Windows and Cuts</title><link>https://opentimegrapher.org/math/m6-averaging-windows-and-cuts/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m6-averaging-windows-and-cuts/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>A reading is never one beat. It is built in layers, each made only from
the one above it:&lt;/p>
&lt;div class="highlight">&lt;pre tabindex="0" class="chroma">&lt;code class="language-text" data-lang="text">&lt;span class="line">&lt;span class="cl">Sound
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl"> ↓ beats found (M1)
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl">Beats: time, number, quality
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl"> ↓ placed on true time (M3); cuts and masks applied
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl">Rate fit: one line through every good beat in the span (M2)
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl">10 s rate windows: a rate fit every 5 s, overlapping by half
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl">2 s windows: each side&amp;#39;s beats averaged into one shape (M4, M5)
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl"> ↓
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl">Reading: rate as fitted; amplitude and beat error as the median of
&lt;/span>&lt;/span>&lt;span class="line">&lt;span class="cl">the 2 s windows; each with its ± (M7) and chips
&lt;/span>&lt;/span>&lt;/code>&lt;/pre>&lt;/div>&lt;h2 id="how-it-is-worked-out">How It Is Worked Out&lt;/h2>
&lt;p>&lt;strong>The span.&lt;/strong> While listening, a reading covers the last &lt;strong>Average Over&lt;/strong>
seconds (10 s unless changed). For a stopped or opened take, the whole
take&amp;rsquo;s reading covers each position&amp;rsquo;s measured stretch.&lt;/p></description></item><item><title>7. The Tick Tock Profile and the Scope</title><link>https://opentimegrapher.org/guide/07-profile-and-scope/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/07-profile-and-scope/</guid><description>&lt;p>Two panes show the sound itself. The &lt;strong>Tick Tock Profile&lt;/strong> shows the
average sound of a beat, with the marks every reading is timed from. The
&lt;strong>Scope&lt;/strong> shows single beats as the microphone heard them.&lt;/p>
&lt;p>They share a place under the Paper Strip, as two tabs. The Profile is in
front when the app starts.&lt;/p>
&lt;h2 id="the-tick-tock-profile">The Tick Tock Profile&lt;/h2>
&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/profile.png" alt="The Tick Tock Profile, marks 1 to 12">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> the typical sound of the Ticks (blue) and of the Tocks
(orange) over the last Average Over time: the same beats the readings
come from. The plot runs from 20 ms before the drop to 8 ms after it.&lt;/p></description></item><item><title>M7. The ± and Correlated Readings</title><link>https://opentimegrapher.org/math/m7-the-plus-minus/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m7-the-plus-minus/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>The &lt;strong>±&lt;/strong> beside a figure is its &lt;strong>standard error&lt;/strong>: an estimate, from the
take itself, of how far the figure would likely move if the same stretch
were heard again under the same conditions.&lt;/p>
&lt;p>It is &lt;strong>precision, not accuracy&lt;/strong>. A wrong lift angle or an uncorrected
sound card clock moves the figure without widening the ±.&lt;/p>
&lt;h2 id="how-it-is-worked-out">How It Is Worked Out&lt;/h2>
&lt;p>The ± comes from the short readings inside the span, in time order: the
2 s windows for amplitude and beat error, and every other 10 s rate
window for the rate.&lt;/p></description></item><item><title>8. Charts and Distributions</title><link>https://opentimegrapher.org/guide/08-charts-and-distributions/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/08-charts-and-distributions/</guid><description>&lt;p>Two panes look at the whole take, not just the last few seconds:&lt;/p>
&lt;ul>
&lt;li>&lt;strong>Charts&lt;/strong> show each reading over time: rate, amplitude and beat error,
from the take&amp;rsquo;s start to its end.&lt;/li>
&lt;li>&lt;strong>Distributions&lt;/strong> show how each reading&amp;rsquo;s values spread, with time order
left out.&lt;/li>
&lt;/ul>
&lt;p>Both start hidden. They open from &lt;strong>Analysis&lt;/strong> in the icon bar, as tabs
beside the Tick Tock Profile.&lt;/p>
&lt;h2 id="charts">Charts&lt;/h2>
&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/charts.png" alt="The Charts pane with all three charts over the first 54 hours of a run-down, marks 1 to 5">&lt;/p></description></item><item><title>M8. Positions Test Figures</title><link>https://opentimegrapher.org/math/m8-positions-test-figures/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m8-positions-test-figures/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>A watch runs at a slightly different rate in each position, because
gravity acts on the balance differently in each. A &lt;strong>positions test&lt;/strong>
measures it in several positions and sums the differences in a few
figures. The Positions Test pane (chapter 20) gives them, and so does
&lt;code>timegrapher session&lt;/code>. They follow the figures Witschi&amp;rsquo;s timegraphers
use and the Swiss standard NIHS 93-10 (NIHS: Normes de l&amp;rsquo;Industrie Horlogère
Suisse, the Swiss watch industry&amp;rsquo;s standards; the project&amp;rsquo;s
&lt;a href="https://github.com/peterhudson/timegrapher/blob/v1.0.1/docs/developer/math-standards.md">math standards&lt;/a> list them).&lt;/p></description></item><item><title>9. Steadiness: What It Is For, the Toolbar and Info</title><link>https://opentimegrapher.org/guide/09-steadiness/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/09-steadiness/</guid><description>&lt;p>The readings cards give one number for each reading. The Charts show it
over time. &lt;strong>Steadiness&lt;/strong> asks how it behaves over time: whether the rate,
the amplitude or the beat error holds one level, steps to another, drifts,
wanders, or repeats on a cycle. It runs a set of statistical tests on the
readings and shows what each one found.&lt;/p>
&lt;p>It states what it finds, with the figures behind it. It doesn&amp;rsquo;t say
whether that is good or bad for a watch: that is yours to judge.&lt;/p></description></item><item><title>M9. Steadiness Statistics</title><link>https://opentimegrapher.org/math/m9-steadiness-statistics/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m9-steadiness-statistics/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>Steadiness (chapters 9 to 18) runs a family of tests on the readings of
each series in time order, and names what passes. This note gives the
statistics behind the Info panel&amp;rsquo;s figures and the views: the scatter,
the outlier rule, the Allan deviation, the trend, the CUSUM (cumulative sum), the change
finder and Holm&amp;rsquo;s correction. The period search has its own note (M10),
and the autocorrelation is in chapter 13.&lt;/p></description></item><item><title>10. Readings Over Time</title><link>https://opentimegrapher.org/guide/10-readings-over-time/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/10-readings-over-time/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-readings.png" alt="Readings Over Time, the rate over the first 12 hours of a run-down, marks 1 to 5">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> every reading the tests read, in time order, with the
levels the tests found drawn over them.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> it is the plainest view of what the other views
test. A step, a slide, two levels or a cycle that a test names should be
visible here, and so should the stray readings that a test is right to
look past.&lt;/p></description></item><item><title>M10. Finding Cycles</title><link>https://opentimegrapher.org/math/m10-finding-cycles/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m10-finding-cycles/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>The &lt;strong>period search&lt;/strong> looks for periods the readings repeat at, scores how
sure it is of each, and names the wheel each one matches. Its scores are
what Periods draws (chapter 11), its lines are what the headline names,
and its cycle is what Cycle folds (chapter 12).&lt;/p>
&lt;h2 id="how-it-is-worked-out">How It Is Worked Out&lt;/h2>
&lt;ol>
&lt;li>
&lt;p>&lt;strong>The watch&amp;rsquo;s own clock.&lt;/strong> Each beat is placed at its number times the
nominal beat period, not at the time the sound card heard it. A wheel
turns once in a fixed number of beats: the fourth wheel once a minute
is 480 beats at 28,800 bph, and the escape wheel&amp;rsquo;s turn is twice its
teeth in beats:&lt;/p></description></item><item><title>11. Periods</title><link>https://opentimegrapher.org/guide/11-periods/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/11-periods/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-periods.png" alt="Periods, the rate over the first 12 hours of a run-down, marks 1 to 9">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> how strongly the readings repeat at each period, from
seconds up to many minutes, on a log scale. A tall, narrow line is a
period the readings repeat at. The calibre&amp;rsquo;s wheels&amp;rsquo; periods are marked
across it.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> anything that turns with a wheel and disturbs the
beat once a turn shows here as a line at that wheel&amp;rsquo;s period. This is where you look for a fault that comes and goes on a
regular beat.&lt;/p></description></item><item><title>M11. Time and Frequency Maps</title><link>https://opentimegrapher.org/math/m11-time-and-frequency-maps/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m11-time-and-frequency-maps/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>Three views break a series into periods: the &lt;strong>FFT&lt;/strong> (Fast Fourier Transform, chapter 16) over the
whole take, and the &lt;strong>STFT Map&lt;/strong> (Short-Time Fourier Transform) and &lt;strong>Wavelet Map&lt;/strong> (chapters 17 and 18)
at each time of it. This note gives how each size is worked out, and
what each method trades.&lt;/p>
&lt;p>All three give a period&amp;rsquo;s size as a &lt;strong>sine&amp;rsquo;s size&lt;/strong>: half its peak to
peak, in the series&amp;rsquo; unit. For the rate that is the beat timing, in ms,
except the FFT&amp;rsquo;s default, which converts it to the swing in rate readings
(below).&lt;/p></description></item><item><title>12. Cycle</title><link>https://opentimegrapher.org/guide/12-cycle/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/12-cycle/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-cycle.png" alt="Cycle, the rate over 12 hours folded at the amplitude&amp;rsquo;s 4-minute cycle, marks 1 to 5">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> the readings folded at one period, so each cycle is
laid over the one before. Along the bottom is the time into the cycle,
from 0 to one period. The line is the cycle&amp;rsquo;s typical shape.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> Periods says the readings repeat at a period. Cycle
shows what one repeat looks like: a smooth wave, or a dip at one point in
the turn. It also shows how big it is, and whether it held through the
take.&lt;/p></description></item><item><title>M12. Isochronism and Rate against Amplitude</title><link>https://opentimegrapher.org/math/m12-isochronism-and-rate-against-amplitude/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/math/m12-isochronism-and-rate-against-amplitude/</guid><description>&lt;h2 id="what-it-is">What It Is&lt;/h2>
&lt;p>A balance is &lt;strong>isochronous&lt;/strong> when its period doesn&amp;rsquo;t depend on how far it
swings. A real one isn&amp;rsquo;t quite: the hairspring, the escapement&amp;rsquo;s impulse
and the balance&amp;rsquo;s poise all make the period move a little with the
amplitude. As the mainspring lets down, the amplitude falls, so a watch&amp;rsquo;s
rate moves through the day with it.&lt;/p>
&lt;p>The Isochronism pane (chapter 19) measures that: the rate at each
amplitude, the slope of rate against amplitude, and where the rate
changes least. The Positions Test&amp;rsquo;s full wind against 24 hours (chapter
20, M8) measures it another way: the change in each position between two
states of wind.&lt;/p></description></item><item><title>13. Autocorrelation</title><link>https://opentimegrapher.org/guide/13-autocorrelation/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/13-autocorrelation/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-autocorrelation.png" alt="Autocorrelation of the rate over the first 12 hours of a run-down, marks 1 to 4">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> how much each reading resembles the one a given time
later, the &lt;strong>lag&lt;/strong>, from 0 up to 10 minutes, or a third of the take if
that is shorter. 1 is the same, 0 is no
resemblance, below 0 is opposite.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> to know whether the readings are independent, each
one a fresh draw, or whether each follows the last. It also finds a
repeat that the period search may score too low to list.&lt;/p></description></item><item><title>14. Allan Deviation</title><link>https://opentimegrapher.org/guide/14-allan-deviation/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/14-allan-deviation/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-allan.png" alt="Allan Deviation of the rate over the first 12 hours of a run-down, marks 1 to 5">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> how much the average of the readings scatters as the
average gets longer. Along the bottom is the &lt;strong>averaging time&lt;/strong>, τ (tau);
up the side, the scatter of averages that long, in the series&amp;rsquo; own unit.
Both axes are logarithmic. Lower is steadier.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> to find out whether averaging longer actually helps.
For a watch whose rate only jitters from one moment to the next, a longer
average is always steadier. For one that wanders, drifts or cycles, it
stops helping past some averaging time, and the curve shows where. It is
the standard way clocks and oscillators are compared for stability (M9).&lt;/p></description></item><item><title>15. CUSUM (Cumulative Sum) and Change Points</title><link>https://opentimegrapher.org/guide/15-cusum-and-change-points/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/15-cusum-and-change-points/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-cusum.png" alt="CUSUM of the rate over the first 12 hours of a run-down, marks 1 to 3">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> the &lt;strong>CUSUM&lt;/strong>, the cumulative sum: the running total of
each reading&amp;rsquo;s distance from the mean of all of them, scaled so that the
same lines hold for any take. With no change of level the total wanders
about 0. Where the level changes, it turns.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> to tell whether the level of a series changed during
the take, and when. A step of a fraction of the scatter is hard to see in
the readings themselves; the running total adds it up reading after
reading until it stands out. It is how you check a knock, a change of
wind or a change in the watch that you suspect moved the rate.&lt;/p></description></item><item><title>16. FFT (Fast Fourier Transform)</title><link>https://opentimegrapher.org/guide/16-fft/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/16-fft/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-fft.png" alt="FFT of the rate&amp;rsquo;s beat timing, Timing on, over the first 12 hours of a run-down, marks 1 to 6">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> the &lt;strong>amplitude spectrum&lt;/strong> of each series, worked out
by the &lt;strong>Fast Fourier Transform&lt;/strong> (FFT), the standard way to split a
series into the regular swings it holds: how big a
regular swing the readings hold at each period, in the series&amp;rsquo; own unit.
Both axes are logarithmic. It is the view a commercial timegrapher&amp;rsquo;s FFT
gives.&lt;/p></description></item><item><title>17. STFT Map (Short-Time Fourier Transform)</title><link>https://opentimegrapher.org/guide/17-stft-map/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/17-stft-map/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-stft.png" alt="STFT Map of the rate&amp;rsquo;s beat timing on the dB scale, over the first 12 hours of a run-down, marks 1 to 8">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> the size of each period&amp;rsquo;s swing at each time of the
take. Up the side is the period, on a log scale, the longest at the top;
across is the time of the take. Each cell&amp;rsquo;s colour is the size, from dark
purple for the smallest to yellow for the largest. It is made from the
&lt;strong>Short-Time Fourier Transform&lt;/strong> (STFT): the Fast Fourier Transform
(FFT) of each 20 minutes of readings, stepped 5 minutes.&lt;/p></description></item><item><title>18. Wavelet Map</title><link>https://opentimegrapher.org/guide/18-wavelet-map/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/18-wavelet-map/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/steady-wavelet.png" alt="Wavelet Map of the rate&amp;rsquo;s beat timing over the first 12 hours of a run-down, marks 1 to 5">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> like the STFT Map (chapter 17), the size of each
period&amp;rsquo;s swing at each time of the take: period up the side, on a log
scale, time across, size as colour. It is made from a &lt;strong>wavelet
transform&lt;/strong>. A wavelet is a short burst of a wave, a few swings long;
the transform slides one along the readings at each period, stretched
to fit, and records how well it matches. So it reads each period over
a time to suit it: short periods over a short time, long ones over a
long time.&lt;/p></description></item><item><title>19. Isochronism</title><link>https://opentimegrapher.org/guide/19-isochronism/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/19-isochronism/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/isochronism.png" alt="Isochronism, the Curve view, over the first 44 hours of a run-down from full wind, marks 1 to 6">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> the rate at each amplitude. As the mainspring lets
down, the balance swings less, and a watch&amp;rsquo;s rate moves with it. The pane
sorts the take&amp;rsquo;s 10 s rate readings by the amplitude of the same reading,
2° at a time, and shows the rate in each step and the curve through
them.&lt;/p></description></item><item><title>20. Positions Test</title><link>https://opentimegrapher.org/guide/20-positions-test/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/20-positions-test/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/positions-test.png" alt="A guided Positions Test measuring the sixth position, marks 1 to 16">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> the rate, amplitude and beat error in each of the six
positions, and the figures that sum up how they differ.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> a watch runs at a different rate in each position,
and on the wrist it turns through all of them. A positions test shows how
much the positions differ and which one stands out, which is what you
need before regulating, and what you compare after a service. Run once
at full wind and again 24 hours later, it also shows how the rate moves
as the mainspring lets down.&lt;/p></description></item><item><title>21. Power Reserve Test</title><link>https://opentimegrapher.org/guide/21-power-reserve-test/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/21-power-reserve-test/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/power-reserve.png" alt="Power Reserve filled from a 60-hour take that ran until the watch stopped, the Paper Strip above, marks 1 to 9">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> how long the watch runs from full wind until it stops,
in one position, and how its rate, amplitude and beat error change hour
by hour on the way.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> the power reserve is how long a full wind lasts.
A watch that stops well short of its calibre&amp;rsquo;s figure, or whose amplitude
falls away early, can point to the mainspring, its lubrication or the
barrel. The hour table also shows how the rate moves as the mainspring
lets down, the same thing Isochronism (chapter 19) reads by amplitude.&lt;/p></description></item><item><title>22. The Watches View</title><link>https://opentimegrapher.org/guide/22-watches-view/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/22-watches-view/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/watches-view.png" alt="The Watches view with a watch picked and one of its takes, marks 1 to 15">&lt;/p>
&lt;p>&lt;strong>What it shows:&lt;/strong> your watches, each with its details, photos and every
take made of it, newest first, with each take&amp;rsquo;s rate, amplitude and beat
error.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> a watch&amp;rsquo;s history in one place. Comparing a take
from before a service with one from after, or this month&amp;rsquo;s with last
month&amp;rsquo;s, is how you see whether a change held. Taking a watch from
here also gives each new take that watch&amp;rsquo;s calibre, lift angle and beat
rate, so you don&amp;rsquo;t set them again each time.&lt;/p></description></item><item><title>23. Takes and Sound Files</title><link>https://opentimegrapher.org/guide/23-takes-and-sound-files/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/23-takes-and-sound-files/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/take-menu.png" alt="A take&amp;rsquo;s menu in the Watches view, marks 1 to 5">&lt;/p>
&lt;p>&lt;strong>What it covers:&lt;/strong> what a take is on disk, how it is kept as it is
heard, how to open a recording made elsewhere, and how to keep a long
take&amp;rsquo;s readings without its sound.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> a take holds the sound itself, not just the
figures, so it can be read again later by a newer app, checked from the
command line, or sent with a problem report. Knowing where it is and
what is in it lets you back it up, move it, or free the disk without
losing what matters.&lt;/p></description></item><item><title>24. Settings and Calibres</title><link>https://opentimegrapher.org/guide/24-settings-and-calibres/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/24-settings-and-calibres/</guid><description>&lt;p>&lt;img src="https://opentimegrapher.org/docs-images/settings-watches-folder.png" alt="Settings at Watches Folder, marks 1 to 4">&lt;/p>
&lt;p>&lt;strong>What it covers:&lt;/strong> the Settings window&amp;rsquo;s General and Watches Folder
pages, and Manage Calibres, where you look up any calibre&amp;rsquo;s beat rate,
lift angle and wheels, add what you know, and keep a short list.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> the calibre decides the lift angle the amplitude
is worked out from, and the wheels Steadiness names its cycles after. A
calibre missing from the list, or a wheel nobody has given, is yours to
add, and every take of that calibre then uses it.&lt;/p></description></item><item><title>25. The Command Line</title><link>https://opentimegrapher.org/guide/25-command-line/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/25-command-line/</guid><description>&lt;p>&lt;strong>What it is:&lt;/strong> &lt;code>timegrapher&lt;/code>, a program run from a terminal, which
measures with the same engine as the app. It reads a recording, or
records one, and prints what it measured as text or JSON (JavaScript Object Notation, a
text format programs read).&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> to read many takes at once, to check a take
outside the app, to put figures in a script or a spreadsheet, or to let
an AI agent drive the timegrapher. Every figure the app shows comes from
the same code, so the two agree on the same sound and settings.&lt;/p></description></item><item><title>26. Claude Desktop</title><link>https://opentimegrapher.org/guide/26-claude-desktop/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/26-claude-desktop/</guid><description>&lt;p>&lt;strong>What it is:&lt;/strong> an extension that lets an AI chat app, such as Claude
Desktop, use the timegrapher: read your recordings, record the watch in
each position, and show the readings as charts in the conversation.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> to ask about a take in plain words (&amp;ldquo;What do these
figures say?&amp;rdquo;, &amp;ldquo;Is the amplitude lower crown down?&amp;rdquo;) and have the answer
come from what was measured, not a guess. The chat app can also guide a
whole positions test, telling you how to place the watch before each
take. It suits someone who would rather ask than read the tables.&lt;/p></description></item><item><title>27. Problems and Reports</title><link>https://opentimegrapher.org/guide/27-problems-and-reports/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/27-problems-and-reports/</guid><description>&lt;p>&lt;strong>What it covers:&lt;/strong> what the app records about itself as it runs, what
it does after it closes unexpectedly, how to make a problem report, and
what to do if the window won&amp;rsquo;t open.&lt;/p>
&lt;p>&lt;strong>Why you&amp;rsquo;d use it:&lt;/strong> a reading that looks wrong is far easier to put
right with the sound that gave it. A report holds that sound, the
figures the app showed, the settings and the log in one zip, with your
name and computer&amp;rsquo;s name taken out, so the problem can be heard and
measured again on another computer.&lt;/p></description></item><item><title>28. Glossary</title><link>https://opentimegrapher.org/guide/28-glossary/</link><pubDate>Mon, 01 Jan 0001 00:00:00 +0000</pubDate><guid>https://opentimegrapher.org/guide/28-glossary/</guid><description>&lt;p>The words this guide uses, each with where to read more.&lt;/p>
&lt;table>
 &lt;thead>
 &lt;tr>
 &lt;th>Word&lt;/th>
 &lt;th>What it means&lt;/th>
 &lt;th>More&lt;/th>
 &lt;/tr>
 &lt;/thead>
 &lt;tbody>
 &lt;tr>
 &lt;td>&lt;strong>AGC&lt;/strong> (automatic gain control)&lt;/td>
 &lt;td>A microphone or sound card turning its own level up and down. Keep it off: it changes the loudness of the sounds the app times.&lt;/td>
 &lt;td>Chapter 3&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Allan deviation&lt;/strong>&lt;/td>
 &lt;td>How the scatter of an average of the readings changes as the average gets longer.&lt;/td>
 &lt;td>Chapter 14, M9&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Amplitude&lt;/strong>&lt;/td>
 &lt;td>How far the balance turns from rest to the end of its swing, in degrees. Worked out from the time from unlock to drop and the lift angle.&lt;/td>
 &lt;td>Chapter 1, M4&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Autocorrelation&lt;/strong>&lt;/td>
 &lt;td>How much each reading follows the one before. Readings that follow each other make a plain ± too small.&lt;/td>
 &lt;td>Chapter 13, M7&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Average Over&lt;/strong>&lt;/td>
 &lt;td>The seconds each live reading covers, 10 s unless set.&lt;/td>
 &lt;td>Chapter 5, M6&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Beat&lt;/strong>&lt;/td>
 &lt;td>One swing of the balance from one end to the other. Two beats make one oscillation.&lt;/td>
 &lt;td>Chapter 1&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Beat error&lt;/strong>&lt;/td>
 &lt;td>Half the difference between the times of the Tick and the Tock halves of the swing, in ms. Shown as a size, without a sign.&lt;/td>
 &lt;td>Chapter 1, M5&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Beat rate (bph)&lt;/strong>&lt;/td>
 &lt;td>Beats per hour the movement is made to make, such as 28,800 bph.&lt;/td>
 &lt;td>Chapter 1&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Bench&lt;/strong>&lt;/td>
 &lt;td>The app&amp;rsquo;s working view: the cards, the Paper Strip and the panes.&lt;/td>
 &lt;td>Chapter 4&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Calibre&lt;/strong>&lt;/td>
 &lt;td>The movement&amp;rsquo;s maker and number. It sets the beat rate, the lift angle and the wheels.&lt;/td>
 &lt;td>Chapters 5, 24&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Change point&lt;/strong>&lt;/td>
 &lt;td>A moment where a reading&amp;rsquo;s level moves and stays moved.&lt;/td>
 &lt;td>Chapter 15, M9&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Clipping&lt;/strong>&lt;/td>
 &lt;td>Sound too loud for the input, cut flat at its top. It spoils the timing of the sounds.&lt;/td>
 &lt;td>Chapter 3&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Clock correction&lt;/strong>&lt;/td>
 &lt;td>The sound card&amp;rsquo;s clock is off by a steady few parts per million (ppm), which moves every rate. Measured with Quartz Correction, from USB lines, or by &lt;code>timegrapher clock&lt;/code>, and taken out.&lt;/td>
 &lt;td>Chapter 3, M3&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>CSV&lt;/strong> (comma-separated values)&lt;/td>
 &lt;td>A plain table file any spreadsheet opens.&lt;/td>
 &lt;td>Chapters 20, 21&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>CUSUM&lt;/strong> (cumulative sum)&lt;/td>
 &lt;td>A running sum of each reading less the mean. A steady slope in it marks a level that changed.&lt;/td>
 &lt;td>Chapter 15, M9&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Cut&lt;/strong>&lt;/td>
 &lt;td>A place no reading may cross: a pause, a jump, a position change, a mask, or over 2 s with no beat.&lt;/td>
 &lt;td>M6&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Cycle&lt;/strong>&lt;/td>
 &lt;td>A rise and fall a reading repeats, often at the period of a wheel.&lt;/td>
 &lt;td>Chapters 11, 12, M10&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>D, DVH, X&lt;/strong>&lt;/td>
 &lt;td>A positions test&amp;rsquo;s largest difference in rate, its vertical less horizontal, and its average.&lt;/td>
 &lt;td>Chapter 20, M8&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>dBFS&lt;/strong> (decibels relative to full scale)&lt;/td>
 &lt;td>Loudness against the loudest the input can record, which is 0 dBFS.&lt;/td>
 &lt;td>Chapter 3&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Drop&lt;/strong>&lt;/td>
 &lt;td>The third sound of a beat: an escape-wheel tooth landing on the other pallet stone. Usually the loudest.&lt;/td>
 &lt;td>Chapter 1&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>DU, DD, CU, CD, CL, CR&lt;/strong>&lt;/td>
 &lt;td>The six positions: dial up, dial down, and crown up, down, left and right. Also written CH, CB, 3H, 6H, 9H, 12H.&lt;/td>
 &lt;td>Chapters 5, 20&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>FFT&lt;/strong> (Fast Fourier Transform)&lt;/td>
 &lt;td>The standard way to split a series into the regular swings it holds. The FFT view gives the size of each period&amp;rsquo;s swing over the whole take.&lt;/td>
 &lt;td>Chapter 16, M11&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>FLAC&lt;/strong> (Free Lossless Audio Codec)&lt;/td>
 &lt;td>A sound file format that keeps every sample in less space than WAV.&lt;/td>
 &lt;td>Chapter 23&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Full wind, 24 hours after&lt;/strong>&lt;/td>
 &lt;td>A positions test run just after winding, and again a day later, to see how the rate moves as the mainspring lets down.&lt;/td>
 &lt;td>Chapter 20&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Ie, Im&lt;/strong>&lt;/td>
 &lt;td>The change in mean rate, and the largest change in one position (crown right left out), from full wind to 24 hours after.&lt;/td>
 &lt;td>Chapter 20, M8&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Impulse&lt;/strong>&lt;/td>
 &lt;td>The second sound of a beat: the escape wheel pushing the pallet stone. Usually the quietest.&lt;/td>
 &lt;td>Chapter 1&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Isochronism&lt;/strong>&lt;/td>
 &lt;td>Whether the rate stays the same as the amplitude falls.&lt;/td>
 &lt;td>Chapter 19, M12&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Jitter&lt;/strong>&lt;/td>
 &lt;td>How far single beats land from the steady line the rate gives.&lt;/td>
 &lt;td>Chapter 5&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>JSON&lt;/strong> (JavaScript Object Notation)&lt;/td>
 &lt;td>A text format programs read; the command line prints it with &lt;code>--json&lt;/code>.&lt;/td>
 &lt;td>Chapter 25&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Lift angle&lt;/strong>&lt;/td>
 &lt;td>The small arc the balance passes through from unlock to drop, set by the movement&amp;rsquo;s design. Every amplitude is in proportion to it.&lt;/td>
 &lt;td>Chapter 1, M4&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Ljung–Box&lt;/strong>&lt;/td>
 &lt;td>A test of whether a series of readings follows itself more than chance would.&lt;/td>
 &lt;td>Chapter 13, M9&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Mask&lt;/strong>&lt;/td>
 &lt;td>A stretch you mark to leave out. Masked time is cut, never filled in.&lt;/td>
 &lt;td>Chapter 6&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>MCP&lt;/strong>&lt;/td>
 &lt;td>The Model Context Protocol, how a chat app such as Claude Desktop uses the timegrapher.&lt;/td>
 &lt;td>Chapter 26&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>NTP&lt;/strong> (Network Time Protocol)&lt;/td>
 &lt;td>How a computer keeps its clock right from internet time servers.&lt;/td>
 &lt;td>Chapter 3, M3&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Paper Strip&lt;/strong>&lt;/td>
 &lt;td>The beats drawn as dots, as a paper timegrapher draws them: a slope is the rate, the gap between the two lines the beat error.&lt;/td>
 &lt;td>Chapter 6&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Period&lt;/strong>&lt;/td>
 &lt;td>The time a cycle takes to repeat. Steadiness names one after the wheel that turns once in it.&lt;/td>
 &lt;td>Chapter 11&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Position Brush&lt;/strong>&lt;/td>
 &lt;td>Marks a stretch of a take as one position, after the fact.&lt;/td>
 &lt;td>Chapter 6&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Positions Test&lt;/strong>&lt;/td>
 &lt;td>The rate, amplitude and beat error in each of six positions, guided or marked.&lt;/td>
 &lt;td>Chapter 20&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Power Reserve Test&lt;/strong>&lt;/td>
 &lt;td>How long a full wind lasts, recorded until the watch stops.&lt;/td>
 &lt;td>Chapter 21&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>ppm&lt;/strong> (parts per million)&lt;/td>
 &lt;td>A clock&amp;rsquo;s error as a fraction: 1 ppm is about 0.086 s a day.&lt;/td>
 &lt;td>Chapter 3, M3&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Quick Listen&lt;/strong>&lt;/td>
 &lt;td>Listening with no watch picked. A take kept goes to Unsorted.&lt;/td>
 &lt;td>Chapter 2&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Rate (s/d)&lt;/strong>&lt;/td>
 &lt;td>How many seconds a day the watch would gain (+) or lose (−) running as it is now.&lt;/td>
 &lt;td>Chapter 1, M2&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Session&lt;/strong>&lt;/td>
 &lt;td>What is on the Bench, from one &lt;strong>New Session&lt;/strong> to the next. A take&amp;rsquo;s &lt;code>session.toml&lt;/code> lists its stretches for the command line&amp;rsquo;s &lt;code>session&lt;/code>.&lt;/td>
 &lt;td>Chapters 23, 25&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Settle&lt;/strong>&lt;/td>
 &lt;td>The seconds after each change of position left out while the balance steadies.&lt;/td>
 &lt;td>Chapter 20, M6&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Steadiness&lt;/strong>&lt;/td>
 &lt;td>The panes that ask how the readings move over a take, and how sure each answer is.&lt;/td>
 &lt;td>Chapter 9&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>STFT map&lt;/strong> (Short-Time Fourier Transform)&lt;/td>
 &lt;td>The FFT of each 20 minutes of readings in turn: each period&amp;rsquo;s size through the take, window by window.&lt;/td>
 &lt;td>Chapter 17, M11&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Take&lt;/strong>&lt;/td>
 &lt;td>One recording of a watch, kept as a folder: its sound, its clock and its settings.&lt;/td>
 &lt;td>Chapter 23&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Tick and Tock&lt;/strong>&lt;/td>
 &lt;td>The app&amp;rsquo;s names for the two kinds of beat, blue and orange. They don&amp;rsquo;t say which pallet stone is which.&lt;/td>
 &lt;td>Chapter 1&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Two states&lt;/strong>&lt;/td>
 &lt;td>Readings flipping between two levels, such as the balance swinging at two amplitudes in turn.&lt;/td>
 &lt;td>Chapter 10&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Unlock&lt;/strong>&lt;/td>
 &lt;td>The first sound of a beat: the impulse pin striking the fork. Amplitude and beat error are timed from it.&lt;/td>
 &lt;td>Chapter 1&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Unsorted&lt;/strong>&lt;/td>
 &lt;td>Where Quick Listen takes wait until filed under a watch.&lt;/td>
 &lt;td>Chapter 22&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Watches folder&lt;/strong>&lt;/td>
 &lt;td>The folder that holds every watch and take, &lt;code>Timegrapher Data&lt;/code> in your home folder unless you chose another.&lt;/td>
 &lt;td>Chapters 22 to 24&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>WAV&lt;/strong> (Waveform Audio File Format)&lt;/td>
 &lt;td>A sound file format that keeps every sample as it is, uncompressed.&lt;/td>
 &lt;td>Chapter 23&lt;/td>
 &lt;/tr>
 &lt;tr>
 &lt;td>&lt;strong>Wavelet map&lt;/strong>&lt;/td>
 &lt;td>Where and when each swing is in the take, sharper in time than the STFT map. A wavelet is a short burst of a wave, stretched to each period and slid along the readings.&lt;/td>
 &lt;td>Chapter 18, M11&lt;/td>
 &lt;/tr>
 &lt;/tbody>
&lt;/table>
&lt;hr>
&lt;p>Previous: &lt;a href="https://opentimegrapher.org/guide/27-problems-and-reports/">Problems and Reports&lt;/a> ·
&lt;a href="https://opentimegrapher.org/guide/">Contents&lt;/a>&lt;/p></description></item></channel></rss>